Pas de rayure et stabilité
Twist rate and stability
Formule de Miller dans les deux sens — tous les calculs sont effectués localement dans votre navigateur.
The Miller formula both ways — all calculations are done locally in your browser.
Ce que cet outil calcule, et ce qu'il ne peut pas calculerWhat this tool calculates, and what it cannot calculate
La formule veut une longueur
Miller a besoin de la longueur de la balle, jamais de son poids. Or c'est le poids qui figure sur la boîte. Cet outil sait passer de l'un à l'autre, mais par une relation calibrée sur des balles match chemisées : elle donne un ordre de grandeur, pas un verdict.
Dès que vous avez la longueur publiée par le fabricant, saisissez-la : elle prime toujours sur l'estimation.
Quelle cible viser
Sg = 1,5 est le seuil à partir duquel la balle atteint son CB annoncé. En dessous, elle vole droit mais avec un lacet résiduel qui coûte de la portée.
Sg = 2,0 est la valeur que Miller recommande pour dimensionner un canon : la marge absorbe l'air froid et dense, où Sg s'effondre.
Il n'y a pas de plafond gênant : la « sur-stabilisation » est un mythe démenti par la mesure.
Deux familles à part
Monobloc cuivre : plus long à masse égale (+8 % mesuré), soit 20 % de Sg en moins. Raisonner au poids y est systématiquement trop optimiste.
Pointe plastique : plus longue aussi, mais le plastique ne pèse rien dans les moments d'inertie. Le mode « vérifier » accepte la longueur métallique et applique alors la formule amendée de Courtney et Miller.
The formula needs a length
Miller needs the bullet's length, never its weight. Yet it is the weight that is printed on the box. This tool can go from one to the other, but through a relation calibrated on jacketed match bullets: it gives an order of magnitude, not a verdict.
As soon as you have the length published by the manufacturer, enter it: it always takes precedence over the estimate.
Which target to aim for
Sg = 1.5 is the threshold from which the bullet achieves its advertised BC. Below it, the bullet flies straight but with a residual yaw that costs range.
Sg = 2.0 is the value Miller recommends for specifying a barrel: the margin absorbs cold, dense air, where Sg collapses.
There is no troublesome ceiling: “over-stabilisation” is a myth disproved by measurement.
Two families apart
Monolithic copper: longer for the same mass (+8 % measured), i.e. 20 % less Sg. Reasoning by weight is systematically too optimistic for them.
Plastic tip: longer too, but the plastic weighs nothing in the moments of inertia. The “check” mode accepts the metal length and then applies the amended formula of Courtney and Miller.
BalleBullet
CanonBarrel
ConditionsConditions
Sources. Don Miller, A New Rule for Estimating Rifling Twist, Precision Shooting, mars 2005, p. 43-48 (texte intégral, archive du Web) — formule, corrections de vitesse et d'atmosphère, et recommandation de dimensionner sur Sg = 2,0. M. Courtney et D. Miller, A Stability Formula for Plastic-Tipped Bullets, Precision Shooting, janvier 2012 (arXiv:1410.5340). Seuil de plein CB : Bryan Litz, Applied Ballistics for Long Range Shooting. La relation masse ↔ longueur est un ajustement propre à ce site, calibré sur neuf balles match à longueur publiée ; elle n'engage aucun des auteurs ci-dessus.
Sources. Don Miller, A New Rule for Estimating Rifling Twist, Precision Shooting, March 2005, pp. 43-48 (full text, Web archive) — formula, velocity and atmosphere corrections, and the recommendation to size on Sg = 2.0. M. Courtney and D. Miller, A Stability Formula for Plastic-Tipped Bullets, Precision Shooting, January 2012 (arXiv:1410.5340). Full-BC threshold: Bryan Litz, Applied Ballistics for Long Range Shooting. The mass ↔ length relation is a fit specific to this site, calibrated on nine match bullets with published length; none of the authors above is responsible for it.